Permatex Steel Reinforced Cold Weld Fuel Oil Resistant 56g
A 15-minute, two-part adhesive and filler system that eliminates the need for welding or brazing. It repairs, fills and bonds to iron, steel, brass, bronze, aluminum and copper. Once cured, it can be drilled, tapped, threaded, filed, sanded and painted. Resists most automotive, shop and cleaning fluids. Withstands temperatures to 300°F intermittent. Over 3,000 PSI shear strength on steel.
Automobile
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
Heavy Duty
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
Marine
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
PRODUCT BENEFITS
• No heating required
• Holds in 10 minutes
• Useable in 30 minutes
• Good moisture resistance
• Withstands extreme temperatures
• Non-flammable
TYPICAL APPLICATIONS
• Cracked transmission cases
• Chipped heads
• Rear end castings
• Cracked blocks
• Cracked intake manifolds
• Damaged keyways
• Split stampings
DIRECTIONS FOR USE
1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease and oil.
2. Roughen smooth surfaces to be repaired with sandpaper.
3. Apply in ventilated area. Vapors may irritate eyes and nose.
4. Squeeze out equal amounts of bonding agent and curing agent.
5. Mix together thoroughly until color is uniform.
6. Apply immediately to both surfaces and press together. Remove excess glue at once.
7. Allow bond to set for 10 minutes before moving or handling.
8. After 24 hours, typical shear strength on steel is 3000 PSI.
9. Cure time will be slower in colder weather.
For Cleanup
1. Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup.
2. Clean hands with Permatex Fast Orange hand cleaners.
Chemical / Solvent Resistance
The product retains effective properties when in contact with water, oil, fuels, and most solvents. Not recommended for long term exposure to chemicals and solvents.
NOTE: Permatex Cold Weld Bonding Compound will not bond polyethylene and polypropylene plastics.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
Original: $17.14
-65%$17.14
$6.00Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
A 15-minute, two-part adhesive and filler system that eliminates the need for welding or brazing. It repairs, fills and bonds to iron, steel, brass, bronze, aluminum and copper. Once cured, it can be drilled, tapped, threaded, filed, sanded and painted. Resists most automotive, shop and cleaning fluids. Withstands temperatures to 300°F intermittent. Over 3,000 PSI shear strength on steel.
Automobile
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
Heavy Duty
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
Marine
Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings
PRODUCT BENEFITS
• No heating required
• Holds in 10 minutes
• Useable in 30 minutes
• Good moisture resistance
• Withstands extreme temperatures
• Non-flammable
TYPICAL APPLICATIONS
• Cracked transmission cases
• Chipped heads
• Rear end castings
• Cracked blocks
• Cracked intake manifolds
• Damaged keyways
• Split stampings
DIRECTIONS FOR USE
1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease and oil.
2. Roughen smooth surfaces to be repaired with sandpaper.
3. Apply in ventilated area. Vapors may irritate eyes and nose.
4. Squeeze out equal amounts of bonding agent and curing agent.
5. Mix together thoroughly until color is uniform.
6. Apply immediately to both surfaces and press together. Remove excess glue at once.
7. Allow bond to set for 10 minutes before moving or handling.
8. After 24 hours, typical shear strength on steel is 3000 PSI.
9. Cure time will be slower in colder weather.
For Cleanup
1. Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup.
2. Clean hands with Permatex Fast Orange hand cleaners.
Chemical / Solvent Resistance
The product retains effective properties when in contact with water, oil, fuels, and most solvents. Not recommended for long term exposure to chemicals and solvents.
NOTE: Permatex Cold Weld Bonding Compound will not bond polyethylene and polypropylene plastics.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
